HanicalSimple Machines and its Mechanical Advantage What are Simple Machines ? What do we mean by Mechanical Advantage? Simple Machines * creates a greater output force than the input force Therefore since work is performed by applying a force over a distance, with the use of these machines we can do more work with lesser effort than working with our bare hands. In short, they make work easier. Mechanical Advantage * The Ratio between the input force and the output force. * The measure of the force amplification achieved by using a tool, mechanical device or machine system. Anyway what is input and output force? Input refers to the force you applied while output refers to the resultant force the object has from the input force. Example: I pushed a ball with 10 N of force, it is rolling with 10 N of force. I input 10 N into it, now it is outputting 10 N. The Six Classical Simple Machines The Lever(French word that means “to raise”) * A simple machine that allows you to gain a mechanical advantage in moving an object or in applying a force to an object. It is considered a "pure" simple machine because friction is not a factor to overcome, as in other simple machines . Part | Description | Fulcrum | Is where a solid board or rod can pivot...
Simple Machines Examples With Pictures Essay
Applied Force Other First Class Lever Examples Applied Force Action Force Spring Load Force Action http://library.thinkquest.org/J002079F/lever.htm Third Class Lever Effort or Applied Force Egg ready to be launched Release hook Compressed Spring Load or Resistance Fulcrum Applied force can be in any direction http://www.usoe.k12.ut.us/curr/science/sciber00/8th/machines /sciber/lever3.htm http://www.usoe.k12.ut.us/curr/science/sciber00/8th/machines /images/tweezer.gif http://www.usoe.k12.ut.us/curr/science/sciber00/8th/machines /images/base.jpg Inclined Plane An inclined plane is a slanted surface used to raise an object. An inclined plane decreases the size of the effort force needed to move an object. However, the distance through which the effort force is applied is increased. The Big Rock rolling downhill with gravitational force IS NOT an example of an inclined plane. The inclined plane gives you mechanical advantage AGAINST gravity. Big Rock http://www.sirinet.net/~jgjohnso/simple.html An example of how an Inclined Plane can be used to raise a mass to activate another simple machine Egg ready to be launched By First Class Lever F Big Rock Force pushing (or pulling) Big Rock up the hill Inclined Plane First Class Lever Wedges Pulleys Wedges are moving inclined planes that are driven under loads to lift Pulleys use a wheel or set of wheels around which a single length (not...
Activity 1.1.2 Simple Machines Practice Problems Answer Key Essay
Activity 1.1.2 Simple Machines Practice Problems Answer Key Procedure Answer the following questions regarding simple machine systems. Each question requires proper illustration and annotation, including labeling of forces, distances, direction, and unknown values. Illustrations should consist of basic simple machine functional sketches rather than realistic pictorials. Be sure to document all solution steps and proper units. All problem calculations should assume ideal conditions and no friction loss. Simple Machines – Lever A first class lever in static equilibrium has a 50lb resistance force and 15lb effort force. The lever’s effort force is located 4 ft from the fulcrum. 1. Sketch and annotate the lever system described above. 2. What is the actual mechanical advantage of the system? Formula Substitute / Solve Final Answer AMA = 3.33 3. Using static equilibrium calculations, calculate the length from the fulcrum to the resistance force. Formula Substitute / Solve Final Answer A wheel barrow is used to lift a 200 lb load. The length from the wheel axle to the center of the load is 2 ft. The length from the wheel and axle to the effort is 5 ft. 4. Illustrate and annotate the lever system described above. 5. What is the ideal mechanical advantage of the system?...
Compound Machine
Our compound machine , consisting of mainly three different simple machines , is a crane designed to multiply your force in order to effectively and efficiently lift the four 75 kg up a steep hill. Our machine starts off with the gear train. As you rotate the handle, all the gears rotate along as well. Since we connected the rope of the pulley to our gears, it then puts the pulley system into action. We created movable pulleys throughout the arm until the tip to stabilize our rope and also give us a mechanical advantage. At the top section of our arm we created a lever to support the load. This magnifies our effort force since a combination of all the mechanical energy is being carried out. With the pulley system, connected all the way to the gear train, and the lever working all together, our mechanical advantage is increased greatly. We created a series of gear trains to not only increase our advantage of torque in the machine but also to increase the mechanical advantage rather than losing efficiency due to friction and thermal energy. Doing this, we magnified our effort force onto the load. Also, in the gears, we arranged it so that the input gear and the output gear gave us a low gear ratio and the idler gears in between. It also allows us to control the direction of our force in the machine . Since it is linked to the pulley, we can control the direction of the rope. However, it only...
Essay
SAMPLE PROBLEMS: . Simple Machines – Lever A first class lever in static equilibrium has a 50lb resistance force and 15lb effort force. The lever’s effort force is located 4 ft from the fulcrum. Sketch and annotate the lever system described above. | What is the actual mechanical advantage of the system? Formula | Substitute / Solve | Final Answer | | | AMA = 3.33 | * Using static equilibrium calculations, calculate the length from the fulcrum to the resistance force. Formula | Substitute / Solve | Final Answer | | | | A wheel barrow is used to lift a 200 lb load. The length from the wheel axle to the center of the load is 2 ft. The length from the wheel and axle to the effort is 5 ft. Illustrate and annotate the lever system described above. | What is the ideal mechanical advantage of the system? Formula | Substitute / Solve | Final Answer | | | | * Using static equilibrium calculations, calculate the effort force needed to overcome the resistance force in the system. Formula | Substitute / Solve | Final Answer | | | | A medical technician uses a pair of four inch long tweezers to remove a wood sliver from a patient. The technician is applying 1 lb of squeezing force to the tweezers. If more than 1/5 lb of force is applied to the sliver, it will break and become difficult to remove. Sketch and annotate the lever system...
Essay on Simple Machines
...Simple machines are extremely important to everyday life. They make stuff that is normally difficult a piece of cake. There are several types of simple machines . The first simple machine is a lever. A lever consists of a fulcrum, load, and effort force. A fulcrum is the support. The placing of the fulcrum changes the amount of force and distance it will take in order to move an object. The load is the applied force. The effort force is the force applied on the opposite side of the load. Levers can be placed in three classes. The 1st class levers are objects like pliers where the fulcrum is at the center of the lever. The 2nd class of levers are objects that have the fulcrum on the opposite side of the applied force like a nutcracker. The 3rd and final class is objects like crab claws. These objects of the load at one end and the fulcrum on the other. An inclined plane is another simple machine . Inclined planes are also known as ramps. Ramps make a trade off between distance and force. No matter how steep the ramp, the work is still the same. A winding road on a mountain side is a good example of a ramp. Some simple machines are modified inclined planes. The wedge is one of those machines . One or two inclined planes make up a wedge. Saws, knives,needles, and axes are made from wedges....
Simple Machines Essay
...Simple Machines Definitions: Machine - A device that makes work easier by changing the speed , direction, or amount of a force. Simple Machine - A device that performs work with only one movement. Simple machines include lever, wheel and axle, inclined plane, screw, and wedge. Ideal Mechanical Advantage (IMA)- A machine in which work in equals work out; such a machine would be frictionless and a 100% efficient IMA= De/Dr Actual Mechanical Advantage (AMA)- It is pretty much the opposite of IMA meaning it is not 100% efficient and it has friction. AMA= Fr/Fe Efficiency- The amount of work put into a machine compared to how much useful work is put out by the machine ; always between 0% and 100%. Friction- The force that resist motion between two surfaces that are touching each other. What do we use machines for? Machines are used for many things. Machines are used in everyday life just to make things easier. You use many machines in a day that you might take for granted. For example a simple ordinary broom is a machine . It is a form of a lever. Our country or world would never be this evolved if it wasn"t for machine . Almost every thing we do has a machine involved. We use machines ...
Simple Machine A machine with few Essay
... Simple Machine : A machine with few or no moving parts. Simple machines make work easier. Examples: Screw, Wheel and Axle, Wedge, Pulley, Inclined Plane, Lever Compound Machine : Two or more simple machines working together to make work easier. Examples: Wheelbarrow, Can Opener, Bicycle Inclined plane: A sloping surface, such as a ramp. Makes lifting heavy loads easier. The trade-off is that an object must be moved a longer distance than if it was lifted straight up, but less force is needed. Examples: Staircase, Ramp Lever: A straight rod or board that pivots on a point known as a fulcrum. Pushing down on one end of a lever results in the upward motion of the opposite end of the fulcrum. Examples: Door on Hinges, Seesaw, Hammer, Bottle Opener Pulley: A wheel that usually has a groove around the outside edge for a rope or belt. Pulling down on the rope can lift an object attached to the rope. Work is made easier because pulling down on the rope is made easier due to gravity. Examples: Flag Pole, Crane, Mini-Blinds Screw: An inclined plane wrapped around a shaft or cylinder. This inclined plane allows the screw to move itself or to move an object or material surrounding it when rotated. Examples: Bolt, Spiral Staircase Wedge: Two inclined planes joined back to back. Wedges are used to split things....
Simple machines are tools that make work easier. They have few or no moving parts.These machines use energy to work. There are six types of simple machines . The six types of simple machines are used in our daily life. Simple machines convert a smaller amount of force exerted over a larger distance to a greater amount of force exerted over a shorter distance, or vice versa. The concept of simple machine was introduced by the Greek philosopher Archimedes the 3rd century.
There are six types of simple machines. The six types of simple machines are
- Wedge
- Lever.
Pulley is wheels and axles with a groove around the outside
A pulley needs a rope, chain or belt around the groove to make it do work
Examples: Flag post, Elevator, Window blinds, Crane, Winch.
A screw is an inclined plane wrapped around a shaft or cylinder.
The inclined plane allows the screw to move itself when rotated
Examples: Screw lid jar, drills, door lock, meat grinder, brace and bits,
3) Wedge:
A wedge is used to split an object through the application of force. It is made up of two inclined planes which meet to form a sharp edge. Wedges are used to split things.
Examples: Knives, axe. Forks, pin, chisels.
An inclined plane is a flat surface that is higher on one end, which makes it easier to move heavy objects to a certain height.
Examples: Roller coaster, stirs, sloping roads, ramps, boat propeller,
The wheel and axle is made up of two circular objects. The wheel is the larger object which turns around the smaller object the axle. The axle is a rod that goes through the wheel which allows the wheel to turn,
Examples: Door knobs, Egg beater, Steering wheels, door knobs, pencil sharpener. Gears are a form of wheels and axles
6) Lever:
This is a is a bar rests on a turning point. The turning point is the fulcrum. An object the lever moves is the load. There are three kinds of levers, First order, Second order and third order.
In a first class lever the fulcrum is in the middle and the load and effort is on either side.
Example: see saw
In a second class lever the fulcrum is at the end, with the load in the Middle.
Example: wheelbarrow
In a third class lever the fulcrum is again at the end, but the effort is in the middle.
Example:
Pair of tweezers.
Advantage of using the six simple machines:
These six simple machines are used in day to day life. They make the work easier for us. Simple machines are being used hundreds of years before. Even the great pyramids were build by using the simple machines. The inclined plane was used to move heavy stones for building the pyramids. Different combinations of these six simple machines can be used in the building of complex machines.
Sub Topics
The effort is the force applied to the machine.
The load is the force against which the machine does the work.
This ratio is a measure of the advantage that one obtains by using the machine. If a load of 40 N is moved by applying an effort of 10 N on the machine then the mechanical advantage of the machine is given by
Velocity Ratio (V.R)
The "corresponding distance" is the distance moved by the load in the same time as the distance moved by the effort.
The velocity ratio depends only on the design of the machine and is always same for a particular machine. The mechanical advantage on the other hand can vary for a particular machine as it depends on friction.
M.A., V.R. and efficiency have no units as they are ratios between similar quantities.
Effort: The force applied to the machine.
Load: The force against which the machine does the work.
Since the effort does the work on the machine and the load is worked upon by the machine, efficiency can also be expressed as
The efficiency is very often expressed as a percentage i.e.,
It should be noted that 100% efficiency is possible only for an ideal (imaginary) machine. Usually, for all practical purposes the efficiency of a machine is always less than 100%. This is because practical M.A. is always less than theoretical M.A. due to friction and the weight of the moving parts.
). The steeper the slope, or incline, the more nearly the required force approaches the actual weight. Expressed mathematically, the force F required to move a block D up an inclined plane without friction is equal to its weight W times the sine of the angle the inclined plane makes with the horizontal (θ). The equation is F = W sin θ.
In this representation of an inclined plane, D represents a block to be moved up the plane, F represents the force required to move the block, and W represents the weight of the block. Expressed mathematically, and assuming the plane to be without friction, F = W sin θ.The principle of the inclined plane is used widely-for example, in ramps and switchback roads, where a small force acting for a distance along a slope can do a large amount of work.
The
A lever is a bar or board that rests on a support called a fulcrum. A downward force exerted on one end of the lever can be transferred and increased in an upward direction at the other end, allowing a small force to lift a heavy weight.
All early people used the lever in some form, for example, for moving heavy stones or as digging sticks for land cultivation. The principle of the lever was used in the swape, or , a long lever pivoted near one end with a platform or water container hanging from the short arm and counterweights attached to the long arm. A man could lift several times his own weight by pulling down on the long arm. This device is said to have been used in Egypt and India for raising water and lifting soldiers over battlements as early as 1500 bce .
The
A wedge is an object that tapers to a thin edge. Pushing the wedge in one direction creates a force in a sideways direction. It is usually made of metal or wood and is used for splitting, lifting, or tightening, as in securing a hammer head onto its handle.
The wedge was used in prehistoric times to split logs and rocks; an is also a wedge, as are the teeth on a saw. In terms of its mechanical function, the screw may be thought of as a wedge wrapped around a cylinder.
The
A wheel and axle is made up of a circular frame (the wheel) that revolves on a shaft or rod (the axle). In its earliest form it was probably used for raising weights or water buckets from wells.
Its principle of operation is best explained by way of a device with a large and a small gear attached to the same shaft. The tendency of a force, F , applied at the radius R on the large gear to turn the shaft is sufficient to overcome the larger force W at the radius r on the small gear. The force amplification, or , is equal to the ratio of the two forces (W :F ) and also equal to the ratio of the radii of the two gears (R :r ).
If the large and small gears are replaced with large- and small-diameter drums that are wrapped with ropes, the wheel and axle becomes capable of raising weights. The weight being lifted is attached to the rope on the small drum, and the operator pulls the rope on the large drum. In this arrangement the mechanical advantage is the radius of the large drum divided by the radius of the small drum. An increase in the mechanical advantage can be obtained by using a small drum with two radii, r 1 and r 2 , and a pulley block. When a force is applied to the large drum, the rope on the small drum winds onto D and off of d.
A measure of the force amplification available with the pulley-and-rope system is the velocity ratio, or the ratio of the at which the force is applied to the rope (V F ) to the velocity at which the weight is raised (V W ). This ratio is equal to twice the radius of the large drum divided by the difference in the radii of the smaller drums D and d. Expressed mathematically, the equation is V F /V W = 2R /(r 2 - r 1). The actual mechanical advantage W /F is less than this velocity ratio, depending on friction. A very large mechanical advantage may be obtained with this arrangement by making the two smaller drums D and d of nearly equal radius.
The
A pulley is a wheel that carries a flexible rope, cord, cable, chain, or belt on its rim. Pulleys are used singly or in combination to transmit and motion. Pulleys with grooved rims are called sheaves. In , pulleys are affixed to shafts at their axes, and power is transmitted between the shafts by means of endless belts running over the pulleys.
One or more independently rotating pulleys can be used to gain mechanical advantage, especially for lifting weights. The shafts about which the pulleys turn may affix them to frames or blocks, and a combination of pulleys, blocks, and rope or other flexible material is referred to as a . The Greek mathematician (3rd century bce ) is reported to have used compound pulleys to pull a ship onto dry land.
The
A screw is a usually circular cylindrical member with a continuous helical rib, used either as a fastener or as a force and motion modifier.
Although the Pythagorean philosopher (5th century bce
) is the alleged inventor of the screw, the exact period of its first appearance as a useful mechanical device is obscure. The invention of the is usually ascribed to Archimedes, but evidence exists of a similar device used for irrigation in Egypt at an earlier date. The screw press, probably invented in Greece in the 1st or 2nd century bce
, has been used since the days of the Roman Empire for pressing clothes. In the 1st century ce
, wooden screws were used in wine and olive-oil presses, and cutters (taps) for cutting internal threads were in use.
Are made in a wide variety of diameters and lengths; when using the larger sizes, pilot holes are drilled to avoid splitting the wood. are large wood screws used to fasten heavy objects to wood. Heads are either square or hexagonal.
Screws that modify force and motion are known as . A screw jack converts (turning moment) to thrust. The thrust (usually to lift a heavy object) is created by turning the screw in a stationary nut. By using a long bar to turn the screw, a small force at the end of the bar can create a large thrust force. Workpiece tables on are moved linearly on guiding ways by screws that rotate in at the ends of the tables and mate with nuts fixed to the machine frame. A similar torque-to-thrust conversion can be obtained by either rotating an axially fixed screw to drive a rotationally fixed nut along the screw or by rotating an axially fixed nut to drive a rotationally fixed screw through the nut.
This article was most recently revised and updated by Robert Curley , Senior Editor.Написанного на Perl . Спустя некоторое время YaBB был переписан на PHP и стал называться YaBB SE .
По мере того как YaBB SE развивался, он становился все больше, и к тому времени появились некоторые аспекты, требующие переделки и усовершенствования проекта. Было принято решение, что лучше всего отделиться от YaBB SE , потому как это было нечто иное, чем YaBB. Самым правильным решением было отказаться от всего что наработано и начать все заново. С этого и началось развитие SMF .
29 сентября 2003 года была выпущена первая версия SMF 1.0 beta1 , которая распространялась только для группы Charter Member . Это было большим минусом, так как форум мог использовать только ограниченный круг людей, входивших в состав данной группы. 10 марта 2004 года вышел первый общедоступный релиз SMF . Веб-форумы на базе SMF 1.1 : ami.lv и не менее популярный iratbildes.lv .
SMF создавался как замена интернет-форуму YaBB SE , который приобрел плохую репутацию из-за проблем его аналога, разработанного на Perl с подобным названием - YaBB .
Первые версии YaBB были известны проблемой производительности и были требовательны к ресурсам. YaBB SE был написан как примерный PHP -порт YaBB , но при этом он был менее требователен к ресурсам и даже лишён проблем с безопасностью.
SMF стартовал как небольшой проект одного из разработчиков YaBB SE , и с целью расширить возможности шаблонов YaBB SE . С тех пор проект постепенно расширялся: добавлялась общая функциональность «заказанная» пользователями, решались проблемы производительности и вопросы безопасности.
Версия 2.0 форума объявлена 8 апреля 2007. Публичный бета-релиз был выпущен 17 марта 2008. К основным нововведениям относятся :
- Абстракция базы данных: планируется поддержка PostgreSQL и SQLite .
- Центр модерации, объединяющий все функции модерации для всех модераторов, а также позволяющий осуществлять премодерацию тем, сообщений и вложений, если это будет необходимо.
- Система предупреждений пользователей
- Дополнительное управление группами пользователей такими как модераторы, а также свободные группы и группы по запросу.
- Поддержка OpenID . Возможность использовать OpenID -аккаунт для регистрации и входа на форум.
- Дополнительные поля в профилях пользователей.
- WYSIWYG -редактор для обеспечения интуитивно понятного интерфейса пользователя.
- Диспетчер задач и система очереди сообщений
Исходный код проекта доступен в публичном репозитории на GitHub github.com/SimpleMachines/SMF2.1
Лицензия
SMF 1.0 и 1.1 публикуются под проприетарной лицензией. В то время как с открытым исходным кодом, перераспределение и / или распространение модифицированных компонентов ограничено уполномоченным органам.
Simple Machines Forum версии 2.0 и 2.1 под лицензией BSD 3-п . Это также открытый исходный код с перераспределением модифицированного кода в зависимости от требований к BSD.
Локализация
Команда SMF
Над SMF работают более 50 человек , в том числе:
- 3 менеджера
- 6 разработчиков
- 3 документатора
Девиз команды: «Малочисленные, гордые, увлечённые!» (The few, the proud, the geeky! (англ.) )
См. также
Напишите отзыв о статье "Simple Machines Forum"
Примечания
Литература
- Phil Hughes (англ.) // Linux Journal . - 2008. - 4 марта.
Ссылки
- - официальный сайт Simple Machines Forum (англ.)
- (рус.)
- (рус.)
|
|||||||||||||||||||||
Отрывок, характеризующий Simple Machines Forum
По опекунским делам рязанского именья, князю Андрею надо было видеться с уездным предводителем. Предводителем был граф Илья Андреич Ростов, и князь Андрей в середине мая поехал к нему.Был уже жаркий период весны. Лес уже весь оделся, была пыль и было так жарко, что проезжая мимо воды, хотелось купаться.
Князь Андрей, невеселый и озабоченный соображениями о том, что и что ему нужно о делах спросить у предводителя, подъезжал по аллее сада к отрадненскому дому Ростовых. Вправо из за деревьев он услыхал женский, веселый крик, и увидал бегущую на перерез его коляски толпу девушек. Впереди других ближе, подбегала к коляске черноволосая, очень тоненькая, странно тоненькая, черноглазая девушка в желтом ситцевом платье, повязанная белым носовым платком, из под которого выбивались пряди расчесавшихся волос. Девушка что то кричала, но узнав чужого, не взглянув на него, со смехом побежала назад.
Князю Андрею вдруг стало от чего то больно. День был так хорош, солнце так ярко, кругом всё так весело; а эта тоненькая и хорошенькая девушка не знала и не хотела знать про его существование и была довольна, и счастлива какой то своей отдельной, – верно глупой – но веселой и счастливой жизнию. «Чему она так рада? о чем она думает! Не об уставе военном, не об устройстве рязанских оброчных. О чем она думает? И чем она счастлива?» невольно с любопытством спрашивал себя князь Андрей.
Граф Илья Андреич в 1809 м году жил в Отрадном всё так же как и прежде, то есть принимая почти всю губернию, с охотами, театрами, обедами и музыкантами. Он, как всякому новому гостю, был рад князю Андрею, и почти насильно оставил его ночевать.
В продолжение скучного дня, во время которого князя Андрея занимали старшие хозяева и почетнейшие из гостей, которыми по случаю приближающихся именин был полон дом старого графа, Болконский несколько раз взглядывая на Наташу чему то смеявшуюся и веселившуюся между другой молодой половиной общества, всё спрашивал себя: «о чем она думает? Чему она так рада!».
Вечером оставшись один на новом месте, он долго не мог заснуть. Он читал, потом потушил свечу и опять зажег ее. В комнате с закрытыми изнутри ставнями было жарко. Он досадовал на этого глупого старика (так он называл Ростова), который задержал его, уверяя, что нужные бумаги в городе, не доставлены еще, досадовал на себя за то, что остался.
Князь Андрей встал и подошел к окну, чтобы отворить его. Как только он открыл ставни, лунный свет, как будто он настороже у окна давно ждал этого, ворвался в комнату. Он отворил окно. Ночь была свежая и неподвижно светлая. Перед самым окном был ряд подстриженных дерев, черных с одной и серебристо освещенных с другой стороны. Под деревами была какая то сочная, мокрая, кудрявая растительность с серебристыми кое где листьями и стеблями. Далее за черными деревами была какая то блестящая росой крыша, правее большое кудрявое дерево, с ярко белым стволом и сучьями, и выше его почти полная луна на светлом, почти беззвездном, весеннем небе. Князь Андрей облокотился на окно и глаза его остановились на этом небе.
Комната князя Андрея была в среднем этаже; в комнатах над ним тоже жили и не спали. Он услыхал сверху женский говор.
– Только еще один раз, – сказал сверху женский голос, который сейчас узнал князь Андрей.
– Да когда же ты спать будешь? – отвечал другой голос.
– Я не буду, я не могу спать, что ж мне делать! Ну, последний раз…
Два женские голоса запели какую то музыкальную фразу, составлявшую конец чего то.
– Ах какая прелесть! Ну теперь спать, и конец.
– Ты спи, а я не могу, – отвечал первый голос, приблизившийся к окну. Она видимо совсем высунулась в окно, потому что слышно было шуршанье ее платья и даже дыханье. Всё затихло и окаменело, как и луна и ее свет и тени. Князь Андрей тоже боялся пошевелиться, чтобы не выдать своего невольного присутствия.
– Соня! Соня! – послышался опять первый голос. – Ну как можно спать! Да ты посмотри, что за прелесть! Ах, какая прелесть! Да проснись же, Соня, – сказала она почти со слезами в голосе. – Ведь этакой прелестной ночи никогда, никогда не бывало.
Соня неохотно что то отвечала.
– Нет, ты посмотри, что за луна!… Ах, какая прелесть! Ты поди сюда. Душенька, голубушка, поди сюда. Ну, видишь? Так бы вот села на корточки, вот так, подхватила бы себя под коленки, – туже, как можно туже – натужиться надо. Вот так!
– Полно, ты упадешь.
Послышалась борьба и недовольный голос Сони: «Ведь второй час».
– Ах, ты только всё портишь мне. Ну, иди, иди.
Опять всё замолкло, но князь Андрей знал, что она всё еще сидит тут, он слышал иногда тихое шевеленье, иногда вздохи.
– Ах… Боже мой! Боже мой! что ж это такое! – вдруг вскрикнула она. – Спать так спать! – и захлопнула окно.
«И дела нет до моего существования!» подумал князь Андрей в то время, как он прислушивался к ее говору, почему то ожидая и боясь, что она скажет что нибудь про него. – «И опять она! И как нарочно!» думал он. В душе его вдруг поднялась такая неожиданная путаница молодых мыслей и надежд, противоречащих всей его жизни, что он, чувствуя себя не в силах уяснить себе свое состояние, тотчас же заснул.
На другой день простившись только с одним графом, не дождавшись выхода дам, князь Андрей поехал домой.
Уже было начало июня, когда князь Андрей, возвращаясь домой, въехал опять в ту березовую рощу, в которой этот старый, корявый дуб так странно и памятно поразил его. Бубенчики еще глуше звенели в лесу, чем полтора месяца тому назад; всё было полно, тенисто и густо; и молодые ели, рассыпанные по лесу, не нарушали общей красоты и, подделываясь под общий характер, нежно зеленели пушистыми молодыми побегами.
Целый день был жаркий, где то собиралась гроза, но только небольшая тучка брызнула на пыль дороги и на сочные листья. Левая сторона леса была темна, в тени; правая мокрая, глянцовитая блестела на солнце, чуть колыхаясь от ветра. Всё было в цвету; соловьи трещали и перекатывались то близко, то далеко.
«Да, здесь, в этом лесу был этот дуб, с которым мы были согласны», подумал князь Андрей. «Да где он», подумал опять князь Андрей, глядя на левую сторону дороги и сам того не зная, не узнавая его, любовался тем дубом, которого он искал. Старый дуб, весь преображенный, раскинувшись шатром сочной, темной зелени, млел, чуть колыхаясь в лучах вечернего солнца. Ни корявых пальцев, ни болячек, ни старого недоверия и горя, – ничего не было видно. Сквозь жесткую, столетнюю кору пробились без сучков сочные, молодые листья, так что верить нельзя было, что этот старик произвел их. «Да, это тот самый дуб», подумал князь Андрей, и на него вдруг нашло беспричинное, весеннее чувство радости и обновления. Все лучшие минуты его жизни вдруг в одно и то же время вспомнились ему. И Аустерлиц с высоким небом, и мертвое, укоризненное лицо жены, и Пьер на пароме, и девочка, взволнованная красотою ночи, и эта ночь, и луна, – и всё это вдруг вспомнилось ему.
UXL Encyclopedia of Science
COPYRIGHT 2002 The Gale Group, Inc.
Machines, simple
A simple machine is a device for doing work that has only one part. Simple machines redirect or change the size of forces, allowing people to do work with less muscle effort and greater speed, thus making their work easier. There are six kinds of simple machines: the lever, the pulley, the wheel and axle , the inclined plane , the wedge, and the screw.
Everyday work
We all do work in our daily lives and we all use simple machines every day. Work as defined by science is force acting upon an object in order to move it across a distance. So scientifically, whenever we push, pull, or cause something to move by using a force, we are performing work. A machine is basically a tool used to make this work easier, and a simple machine is among the simplest tools we can use. Therefore, from a scientific standpoint, we are doing work when we open a can of paint with a screwdriver, use a spade to pull out weeds, slide boxes down a ramp, or go up and down on a see-saw. In each of these examples we are using a simple machine that allows us to achieve our goal with less muscle effort or in a shorter amount of time.
Earliest simple machines
This idea of doing something in a better or easier way or of using less of our own muscle power has always been a goal of humans. Probably from the beginning of human history, anyone who ever had a job to do would eventually look for a way to do it better, quicker, and easier. Most people try to make a physical job easier rather than harder to do. In fact, one of our human predecessors is called Homo habilis, which means "handy man" or "capable man." This early version of our human ancestors was given that name because, although not quite fully human, it had a large enough brain to understand the idea of a tool, as well as hands with fingers and thumbs that were capable of making and using a tool. Therefore, the first simple machine was probably a strong stick (the lever) that our ancestor used to move a heavy object, or perhaps it was a sharp rock (the wedge) used to scrape an animal skin, or something else equally simple but effective. Other early examples might be a rolling log, which is a primitive form of the wheel and axle , and a sloping hill, which is a natural inclined plane . There is evidence throughout all early civilizations that humans used simple machines to satisfy their needs and to modify their environment.
Words to Know
Compound machine: A machine consisting of two or more simple machines.
Effort force: The force applied to a machine.
Fulcrum: The point or support on which a lever turns.
Resistance force: The force exerted by a machine.
Work: Transfer of energy by a force acting to move matter.
The beauty of simple machines is seen in the way they are used as extensions of our own muscles, as well as in how they can redirect or magnify the strength and force of an individual. They do this by increasing the efficiency of our work, as well as by what is called a mechanical advantage. A mechanical advantage occurs when a simple machine takes a small "input" force (our own muscle power) and increases the magnitude of the "output" force. A good example of this is when a person uses a small input force on a jack handle and produces an output force large enough to easily lift one end of an automobile. The efficiency and advantage produced by such a simple device can be amazing, and it was with such simple machines that the rock statues of Easter Island , the stone pillars of Stonehenge, and the Great Pyramids of Egypt were constructed. Some of the known accomplishments of these early users of simple machines are truly amazing. For example, we have evidence that the builders of the pyramids moved limestone blocks weighing between 2 and 70 tons (1.8 and 63.5 metric tons) hundreds of miles, and that they built ramps over 1 mile (1.6 kilometers) long.
Trade-offs of simple machines
One of the keys to understanding how a simple machine makes things easier is to realize that the amount of work a machine can do is equal to the force used, multiplied by the distance that the machine moves or lifts the object. In other words, we can multiply the force we are able to exert if we increase the distance. For example, the longer the inclined plane— which is basically a ramp— the smaller the force needed to move an object. Picture having to lift a heavy box straight up off the ground and place it on a high self. If the box is too heavy for us to pick up, we can build a ramp (an inclined plane) and push it up. Common sense tells us that the steeper (or shorter) the ramp, the harder it is to push the object to the top. Yet the longer (and less steep) it is, the easier it is to move the box, little by little. Therefore, if we are not in a hurry (like the pyramid builders), we can take our time and push it slowly up the long ramp to the top of the shelf.
Understanding this allows us also to understand that simple machines involve what is called a "trade-off." The trade-off, or the something that is given up in order to get something else, is the increase in distance. So although we have to use less force to move a heavy object up a ramp, we have increased the distance we have to move it (because a ramp is not the shortest distance between two points). Most primitive people were happy to make this trade-off since it often meant being able to move something that they otherwise could not have moved.
Today, most machines are complicated and use several different elements like ball bearings or gears to do their work. However, when we look at them closely and understand their parts, we usually see that despite their complexity they are basically just two or more simple machines working together. These are called compound machines. Although some people say that there are less than six simple machines (since a wedge can be considered an inclined plane that is moving, or a pulley is a lever that rotates around a fixed point), most authorities agree that there are in fact six types of simple machines.
Lever
A lever is a stiff bar or rod that rests on a support called a fulcrum (pronounced FULL-krum) and which lifts or moves something. This may be one of the earliest simple machines, because any large, strong stick would have worked as a lever. Pick up a stick, wedge it under one edge of a rock, and push down and you have used a lever. Downward motion on one end results in upward motion on the other. Anything that pries something loose is also a lever, such as a crow bar or the claw end of a hammer. There are three types or classes of levers. A first-class lever has the fulcrum or pivot point located near the middle of the tool and what it is moving (called the resistance force). A pair of scissors and a seesaw are good examples. A second-class lever has the resistance force located between the fulcrum and the end of the lever where the effort force is being made. Typical examples of this are a wheelbarrow, nutcracker, and a bottle opener. A third-class lever has the effort force being applied between the fulcrum and the resistance force. Tweezers, ice tongs, and shovels are good examples. When you use a shovel, you hold one end steady to act as a fulcrum, and you use your other hand to pull up on a load of dirt. The second hand is the effort force, and the dirt being picked up is
the resistance force. The effort applied by your second hand lies between the resistance force (dirt) and the fulcrum (your first hand).
Pulley
A pulley consists of a grooved wheel that turns freely in a frame called a block through which a rope runs. In some ways, it is a variation of a wheel and axle, but instead of rotating an axle, the wheel rotates a rope or cord. In its simplest form, a pulley"s grooved wheel is attached to some immovable object, like a ceiling or a beam. When a person pulls down on one end of the rope, an object at the opposite end is raised. A simple pulley gains nothing in force, speed, or distance. Instead, it only changes the direction of the force, as with a Venetian blind (up or down). Pulley systems can be movable and very complex, using two or more connected pulleys. This permits a heavy load to be lifted with less force, although over a longer distance.
Wheel and axle
The wheel and axle is actually a variation of the lever (since the center of the axle acts as the fulcrum). It may have been used as early as 3000 b.c., and like the lever, it is a very important simple machine. However, unlike the lever that can be rotated to pry an object loose or push a load along, a wheel and axle can move a load much farther. Since it consists of a large wheel rigidly attached to a small wheel (the axle or the shaft), when one part turns the other also does. Some examples of the wheel and axle are a door knob, a water wheel , an egg beater, and the wheels on a wagon, car, or bicycle. When force is applied to the wheel (thereby turning the axle), force is increased and distance and speed are decreased. When it is applied to the axle (turning the wheel), force is decreased and distance and speed are increased.
Inclined plane
An inclined plane is simply a sloping surface. It is used to make it easier to move a weight from a lower to a higher spot. It takes much less effort to push a wheel barrow load slowly up a gently sloping ramp than it does to pick it up and lift it to a higher spot. The trade-off is that the load must be moved a greater distance. Everyday examples are stairs, escalators, ladders, and a ship"s plank.
Wedge
A wedge is an inclined plane that moves and is used to increase force— either to separate something or to hold things together. With a wedge, the object or material remains in place while the wedge moves. A wedge can have a single sloping surface (like a door stop that holds a door tightly in place), or it can have two sloping surfaces or sides (like the wedge that splits a log in two). An axe or knife blade is a wedge, as is a chisel, plow, and even a nail.
Screw
A screw can be considered yet another form of an inclined plane, since it can be thought of as one that is wrapped in a spiral around a cylinder or post. In everyday life, screws are used to hold things together and to lift other things. When it is turned, a screw converts rotary (circular) motion into a forward or backward motion. Every screw has two parts: a body or post around which the inclined plane is twisted, and the thread (the spiraled inclined plane itself). Every screw has a thread, and if you look very closely at it, you will see that the threads form a tiny "ramp"
that runs from the tip to the top. Like nails, screws are used to hold things together, while a drill bit is used to make holes. Other examples of screws are airplane and boat propellers.
In physics, a simple machine is any device that requires the application of only one force in order to perform work. Work is the product of the force applied and the distance moved due to the force. Most authorities list six kinds of simple machines: levers, pulleys, wheels and axles, inclined planes, wedges, and screws. One can argue, however, that these six machines are not entirely different from each other. Pulleys and wheels and axles, for example, are really special kinds of levers, and wedges and screws are special kinds of inclined planes.
Levers
A lever is a simple machine that consists of a rigid bar supported at one point, known as the fulcrum. A force called the effort force is applied at one point on the lever in order to move an object, known as the resistance force, located at some other point on the lever. A common example of the lever is the crow bar used to move a heavy object such as a rock. To use the crow bar, one end is placed under the bar, which is supported at some point (the fulcrum) close to the rock. A person then applies a force at the opposite end of the crow bar to lift the rock. A lever of the type described here is a first-class lever because the fulcrum is placed between the applied force (the effort force) and the object to be moved (the resistance force).
The effectiveness of the lever as a machine depends on two factors: the forces applied at each end and the distance of each force from the fulcrum. The farther a person stands from the fulcrum, the more his or her force on the lever is magnified. Suppose that the rock to be lifted is only one foot from the fulcrum and the person trying to lift the rock stands 2 yd (1.8 m) from the fulcrum. Then, the person’ s force is magnified by a factor of six. If he or she pushes down with a force of 30 lb (13.5 kg), the object that is lifted can be as heavy as 180 (6 x 30) lb (81 kg).
Two other types of levers exist. In one, called a second-class lever, the resistance force lies between the
effort force and the fulcrum. A nutcracker is an example of a second-class lever. The fulcrum in the nutcracker is at one end, where the two metal rods of the device are hinged together. The effort force is applied at the opposite ends of the rods, and the resistance force, the nut to be cracked open, lies in the middle.
In a third-class lever, the effort force lies between the resistance force and the fulcrum. Some kinds of garden tools are examples of third-class levers. When a person uses a shovel, for example, one holds the handle end steady to act as the fulcrum, while using the other hand to pull up on a load of dirt. The second hand is the effort force, and the dirt being picked up is the resistance force. The effort applied by the second hand lies between the resistance force (the dirt) and the fulcrum (the first hand).
Mechanical advantage
The term mechanical advantage is used to described how effectively a simple machine works. Mechanical advantage is defined as the resistance force moved divided by the effort force used. In the lever example above, for example, a person pushing with a force of 30 lb (13.5 kg) was able to move an object that weighed 180 lb (81 kg). So, the mechanical advantage of the lever in that example was 180 lb divided by 30 lb, or 6.
The mechanical advantage described here is really the theoretical mechanical advantage of a machine. In actual practice, the mechanical advantage is always less than what a person might calculate. The main reason for this difference is resistance. When a person does work with a machine, there is always some resistance to that work. For example, a mathematician can calculate the theoretical mechanical advantage of a screw (a kind of simple machine) that is being forced into a piece of wood by a screwdriver. The actual mechanical advantage is much less than what is calculated because friction must be overcome in driving the screw into the wood.
Sometimes the mechanical advantage of a machine is less than one. That is, a person has to put in more force than the machine can move. Class three levers are examples of such machines. A person exerts more force on a class three lever than the lever can move. The purpose of a class three lever, therefore, is not to magnify the amount of force that can be moved, but to magnify the distance the force is being moved.
As an example of this kind of lever, imagine a person who is fishing with a long fishing rod. The person will exert a much larger force to take a fish out of the water than the fish itself weighs. The advantage of the fishing pole, however, is that it moves the fish a large distance, from the water to the boat or the shore.
Pulleys
A pulley is a simple machine consisting of a grooved wheel through which a rope runs. The pulley can be thought of as a kind of lever if one thinks of the grooved wheel as the fulcrum of the lever. Then the effort force is the force applied on one end of the pulley rope, and the resistance force is the weight that is lifted at the opposite end of the pulley rope.
In the simplest form of a pulley, the grooved wheel is attached to some immovable object, such as a ceiling or beam. When a person pulls down on one end of the pulley rope, an object at the opposite end of the rope is raised. In a fixed pulley of this design, the mechanical advantage is one. That is, a person can lift a weight equal to the force applied. The advantage of the pulley is one of direction. An object can be made to move upward or downward with such a pulley. Venetian blinds are a simple example of the fixed pulley.
In a movable pulley, one end of the pulley rope is attached to a stationary object (such as a ceiling or beam), and the grooved wheel is free to move along the rope. When a person lifts on the free end of the rope, the grooved wheel and any attached weight slides upward on the rope. The mechanical advantage of this kind of pulley is two. That is, a person can lift twice as much weight as the force applied on the free end of the pulley rope.
More complex pulley systems can also be designed. For example, one grooved wheel can be attached to a stationary object, and a second movable pulley can be attached to the pulley rope. When a person pulls on the free end of the pulley rope, a weight attached to the movable pulley can be moved upward with a mechanical advantage of two. In general, in more complicated pulley systems, the mechanical advantage of the pulley is equal to the number of ropes that hold up the weight to be lifted. Combinations of fixed and movable pulleys are also known as a block and tackle . Some blocks and tackles have mechanical advantages high enough to allow a single person to lift weights as heavy as that of an automobile.
Wheel and axle
A second variation of the lever is the simple machine known as a wheel and axle . A wheel and axle consists of two circular pieces of different sizes attached to each other. The larger circular piece is the wheel in the system, and the smaller circular piece is the axle. One of the circular pieces can be considered as the effort arm of the lever and the second, the resistance arm. The place at which the two pieces is joined is the fulcrum of the system.
Some examples of the wheel and axle include a door knob, a screwdriver, an egg beater, a water wheel , the steering wheel of an automobile, and the crank used to raise a bucket of water from a well. When the wheel in a wheel and axle machine is turned, so is the axle, and vice versa. For example, when someone turn the handle of a screwdriver, the edge that fits into the screw head turns at the same time.
The mechanical advantage of a wheel and axle machine can be found by dividing the radius of the wheel by the radius of the axle. For example, suppose that the crank on a water well turns through a radius of 2 ft (61 cm) and the radius of the axle around which the rope is wrapped is 4 in (10 cm). Then, the mechanical advantage of this wheel and axle system is 2 ft divided by 4 in, or 6.
Inclined planes
KEY TERMS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compound machineA machine consisting of two or more simple machines.
Effort forceThe force applied to a machine.
FrictionA force caused by the movement of an object through liquid, gas, or against a second object that works to oppose the first object"s movement.
Mechanical advantageA mathematical measure of the amount by which a machine magnifies the force put into the machine.
Resistance forceThe force exerted by a machine.
Learn more about citation styles
Citation styles
сайт gives you the ability to cite reference entries and articles according to common styles from the Modern Language Association (MLA), The Chicago Manual of Style, and the American Psychological Association (APA).
Within the “Cite this article” tool, pick a style to see how all available information looks when formatted according to that style. Then, copy and paste the text into your bibliography or works cited list.
Because each style has its own formatting nuances that evolve over time and not all information is available for every reference entry or article, сайт cannot guarantee each citation it generates. Therefore, it’s best to use сайт citations as a starting point before checking the style against your school or publication’s requirements and the most-recent information available at these sites:
Notes:
- Most online reference entries and articles do not have page numbers.. However, the date of retrieval is often important. Refer to each style’s convention regarding the best way to format page numbers and retrieval dates.
- In addition to the MLA, Chicago, and APA styles, your school, university, publication, or institution may have its own requirements for citations. Therefore, be sure to refer to those guidelines when editing your bibliography or works cited list.